how to fix the P0135 code on my Honda Accord 10th Generation (2018-2022)

Honda Accord 8th Generation (2008-2012)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

Error Code: P0135

3 min read

537 words

Problem Statement

Learn how to diagnose and fix P0135 oxygen sensor heater circuit issues in Honda Accord 10th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Error Code

P0135

Affected Component

Exhaust System

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on the exhaust components.

Symptoms

•Check engine light illuminated
•Poor fuel economy
•Rough idle or stalling
•Increased emissions
•Engine running rich or lean

Diagnostic Steps

1
Scan the vehicle using an OBD-II scanner to confirm the P0135 code and check for any additional codes.
2
Inspect the wiring and connectors associated with Bank 1 Sensor 1 for any visible damage or corrosion.
3
Test the oxygen sensor heater circuit using a multimeter to check for continuity and proper voltage.
4
Check the vehicle's fuses related to the oxygen sensor heater circuit.
5
Inspect the oxygen sensor for carbon buildup or other contaminants.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Wire brush
•Dielectric grease

Parts Required

•New Bank 1 Sensor 1 oxygen sensor (OEM recommended)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle using an OBD-II scanner to confirm the P0135 code and check for any additional codes.
2
Inspect the wiring and connectors associated with Bank 1 Sensor 1 for any visible damage or corrosion.
3
Test the oxygen sensor heater circuit using a multimeter to check for continuity and proper voltage.
4
Check the vehicle's fuses related to the oxygen sensor heater circuit.
5
Inspect the oxygen sensor for carbon buildup or other contaminants.

Solution

1. Preparation

Tools Required: OBD-II scanner, multimeter, socket set, torque wrench, wire brush, dielectric grease.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the negative battery terminal to prevent electrical shorts.

2. Inspect and Repair Wiring

Sub-steps:
1. Remove the vehicle's under-hood cover if applicable to access the oxygen sensor wiring.
2. Visually inspect the wiring and connectors for any signs of wear, damage, or corrosion.
3. Clean any corroded connectors with a wire brush and apply dielectric grease to prevent future corrosion.
4. Repair or replace any damaged wiring as necessary.

3. Replace the Oxygen Sensor

Sub-steps:
1. Locate the Bank 1 Sensor 1 oxygen sensor, which is typically near the exhaust manifold.
2. Disconnect the sensor's electrical connector.
3. Use a socket wrench to remove the old oxygen sensor, taking care not to damage the threads in the exhaust.
4. Apply anti-seize compound to the threads of the new sensor (if applicable).
5. Install the new oxygen sensor and tighten it to the manufacturer's specified torque (usually around 30 ft-lbs).
6. Reconnect the electrical connector.

4. Clear Codes and Test Drive

Sub-steps:
1. Reconnect the negative battery terminal.
2. Use the OBD-II scanner to clear the P0135 code from the ECU.
3. Start the engine and allow it to reach operating temperature.
4. Take the vehicle for a test drive, monitoring engine performance and checking for the re-appearance of the check engine light.