how to check for a bad ignition coil in my Honda Accord 10th Generation (2018-2022)

Honda Accord 8th Generation (2008-2012)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

569 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix ignition coil issues in Honda Accord 10th Generation (2018-2022). Step-by-step guide with symptoms and repair instructions.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on ignition system components.
•Allow the engine to cool before touching any engine parts.

Symptoms

•Check engine light illuminated
•Engine misfires
•Rough idle
•Decreased fuel efficiency
•Increased exhaust emissions
•Difficulty starting the engine

Diagnostic Steps

1
Scan the vehicle using an OBD-II scanner to retrieve any diagnostic trouble codes (DTCs).
2
Inspect the ignition coils visually for any signs of damage, cracks, or corrosion.
3
Measure the primary resistance of each ignition coil using a multimeter.
4
Measure the secondary resistance of each ignition coil using a multimeter.
5
Perform a spark test to check for spark output from the ignition coil.
6
Swap the suspected bad ignition coil with a known good coil to see if the misfire moves to another cylinder.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Torque wrench
•Screwdrivers

Parts Required

•Ignition coil(s) (if replacement is needed)
•Spark plug(s) (consider replacing if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle using an OBD-II scanner to retrieve any diagnostic trouble codes (DTCs).
2
Inspect the ignition coils visually for any signs of damage, cracks, or corrosion.
3
Measure the primary resistance of each ignition coil using a multimeter.
4
Measure the secondary resistance of each ignition coil using a multimeter.
5
Perform a spark test to check for spark output from the ignition coil.
6
Swap the suspected bad ignition coil with a known good coil to see if the misfire moves to another cylinder.

Solution

1. Preparation

Gather all necessary tools and parts.
Disconnect the negative battery terminal to ensure safety while working on the ignition system.

2. Remove Ignition Coil

Locate the ignition coils on the engine (usually near the top of the engine near the spark plugs).
Remove any engine covers if they obstruct access to the ignition coils.
Unplug the electrical connector from the ignition coil by pressing the tab and pulling it out.
Use a socket wrench to remove the bolt securing the ignition coil to the engine.
Carefully pull the ignition coil out of the spark plug well.

3. Inspect and Test Ignition Coil

Visually inspect the ignition coil for any signs of physical damage or corrosion.
Using a multimeter, set it to Ohms and measure the primary resistance by connecting the probes to the positive and negative terminals of the ignition coil. Compare the reading to the specifications provided in the service manual.
Measure the secondary resistance by placing one probe on the high-voltage terminal and the other on the ground terminal. Again, compare this reading to the specifications.

4. Replace Ignition Coil (if necessary)

If the ignition coil is faulty based on the testing, replace it with a new ignition coil.
Install the new ignition coil by reversing the removal steps: insert the coil into the spark plug well, secure it with the bolt, and reconnect the electrical connector.

5. Reconnect Battery and Test

Reconnect the negative battery terminal.
Start the engine and ensure that it runs smoothly without misfires or warning lights.