how to change the brake pads on my Honda Accord 9th Generation (2013-2017)

Honda Accord Eleventh Generation (2023-present)

Error Codes

1-2 hours

Time

medium

Difficulty

high

Severity

3 min read

549 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Step-by-step instructions to change brake pads on Honda Accord (2013-2017). Learn the symptoms, diagnostic steps, and tools required for a successful repair.

Affected Component

Brakes

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always wear safety goggles and gloves when working on brake systems.
•Ensure the vehicle is securely supported on jack stands before working underneath.

Symptoms

•Squeaking or grinding noise when braking
•Reduced braking performance
•Vibration or pulsation in the brake pedal
•Warning light on the dashboard (if equipped)
•Increased brake dust accumulation on wheels

Diagnostic Steps

1
Inspect brake pad thickness through the wheel spokes.
2
Check for any visible damage to the brake rotor surface.
3
Listen for abnormal noises while applying the brakes.
4
Verify that the brake fluid level is adequate in the master cylinder.
5
Assess the condition of the brake calipers and hardware.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Socket set
•C-clamp or brake caliper tool
•Brake cleaner
•Torque wrench
•Safety goggles
•Gloves

Parts Required

•New brake pads
•Brake grease (for caliper slides)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather necessary tools and parts.
Tools Required:
- Jack and jack stands
- Lug wrench
- Socket set
- C-clamp or brake caliper tool
- Brake cleaner
- Torque wrench
- Safety goggles and gloves
Parts Required:
- New brake pads
- Brake grease (for caliper slides)

2. Raise the Vehicle

Park the vehicle on a level surface and engage the parking brake.
Loosen the lug nuts on the front or rear wheels slightly (do not remove).
Use the jack to lift the vehicle and secure it with jack stands.
Remove the lug nuts and take off the wheel.

3. Remove the Brake Caliper

Locate the caliper bolts (typically two bolts on the back of the caliper).
Use a socket set to remove the caliper bolts.
Carefully slide the caliper off the brake rotor. Do not let it hang by the brake line; support it with a bungee cord or similar.

4. Replace the Brake Pads

Remove the old brake pads from the caliper bracket. Note their orientation.
Use a C-clamp or brake caliper tool to compress the caliper piston back into the caliper housing.
Install the new brake pads in the same orientation as the old ones, ensuring they are seated properly.

5. Reinstall the Caliper

Position the caliper back over the new brake pads and rotor.
Reinsert and tighten the caliper bolts to the manufacturer’s specification (typically around 20-25 lb-ft; check service manual for exact specs).
Reattach the wheel and hand-tighten the lug nuts.

6. Lower the Vehicle and Final Checks

Lower the vehicle from the jack stands using the jack.
Tighten the lug nuts to the manufacturer’s specifications using a torque wrench (usually around 80-100 lb-ft).
Repeat the process on the opposite side if necessary.