Honda Accord 9th Generation (2013-2017) brake pedal goes to the floor what could be wrong

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

critical

Severity

4 min read

618 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix a brake pedal that goes to the floor in a 2013-2017 Honda Accord. Step-by-step guide with symptoms and solutions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on any electrical components.
•Allow the vehicle to cool before inspecting the braking system.

Symptoms

•Brake pedal feels spongy or soft
•Brake warning light illuminated on the dashboard
•Reduced braking effectiveness
•Fluid leakage observed around the brake components
•Unusual noises when pressing the brake pedal

Diagnostic Steps

1
Inspect the brake fluid level in the master cylinder reservoir.
2
Check for any visible leaks in the brake lines or around the brake calipers.
3
Scan for error codes using an OBD-II scanner to check for ABS-related issues.
4
Perform a visual inspection of brake pads and rotors for wear or damage.
5
Test the brake booster for proper function by pumping the brake pedal and observing changes in effort required.
6
Check the condition of the brake master cylinder for wear or failure.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Brake fluid
•Wrench set
•Socket set
•Torque wrench
•Brake bleeder kit
•Funnel
•Brake line flaring tool

Parts Required

•Brake master cylinder (if faulty)
•Brake fluid

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the brake fluid level in the master cylinder reservoir.
2
Check for any visible leaks in the brake lines or around the brake calipers.
3
Scan for error codes using an OBD-II scanner to check for ABS-related issues.
4
Perform a visual inspection of brake pads and rotors for wear or damage.
5
Test the brake booster for proper function by pumping the brake pedal and observing changes in effort required.
6
Check the condition of the brake master cylinder for wear or failure.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and engage the parking brake.
Place wheel chocks behind the rear wheels for added safety.

2. Inspect and Replace Brake Fluid

Sub-steps:
1. Open the hood and locate the brake fluid reservoir.
2. If the fluid level is low, add the appropriate DOT fluid (check owner's manual for specification).
3. If the fluid is contaminated, perform a brake fluid flush.
Tools Required: Brake fluid, funnel.

3. Check for Leaks

Sub-steps:
1. Inspect brake lines for any signs of corrosion or damage.
2. Examine brake calipers and wheel cylinders for leaks.
3. Replace any damaged lines or components found during inspection.
Tools Required: Wrench set, brake line flaring tool if necessary.

4. Replace Brake Master Cylinder (if faulty)

Sub-steps:
1. Disconnect the negative battery terminal.
2. Remove the brake fluid from the master cylinder reservoir.
3. Disconnect the brake lines from the master cylinder using the appropriate wrench.
4. Remove the master cylinder mounting bolts and take out the old master cylinder.
5. Install the new master cylinder, torque the mounting bolts to manufacturer specifications (usually around 14-18 lb-ft).
6. Reconnect the brake lines and refill the reservoir with new brake fluid.
Tools Required: Wrench set, socket set, torque wrench.

5. Bleed the Brakes

Sub-steps:
1. Begin at the farthest wheel from the master cylinder (usually the rear passenger side).
2. Attach a clear hose to the bleeder screw and place the other end in a container.
3. Have an assistant pump the brake pedal and hold it down.
4. Open the bleeder screw to allow fluid and air to escape, then close it before your assistant releases the pedal.
5. Repeat until no air bubbles are visible in the fluid.
6. Perform the same process on the rear driver, front passenger, and finish with the front driver wheel.
Tools Required: Brake bleeder kit or clear tubing, wrench.