how to replace a faulty wheel bearing on my Honda Accord

Honda Accord 10th Generation (2018-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

581 words

Problem Statement

Step-by-step guide on how to replace a faulty wheel bearing on your Honda Accord. Includes symptoms, diagnostic steps, tools, and safety warnings.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before starting the work.
•Allow the vehicle to cool if it has been driven recently.

Symptoms

•Grinding or humming noise while driving, especially during turns
•Vibration felt through the steering wheel or floorboard
•Uneven tire wear
•Wheel wobble or looseness
•ABS warning light illuminated (if equipped)

Diagnostic Steps

1
Lift the vehicle using a jack and secure it with jack stands.
2
Spin the wheel by hand to listen for noise and feel for roughness.
3
Inspect the wheel bearing visually for any signs of damage or wear.
4
Check for play in the wheel by pushing and pulling on the top and bottom of the tire.
5
Use an OBD-II scanner to check for any related fault codes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Hammer
•Slide hammer or wheel bearing puller
•Grease
•Jack and jack stands

Parts Required

•New wheel bearing
•Brake caliper hardware (if necessary)
•Cotter pin (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Lift the vehicle using a jack and secure it with jack stands.
2
Spin the wheel by hand to listen for noise and feel for roughness.
3
Inspect the wheel bearing visually for any signs of damage or wear.
4
Check for play in the wheel by pushing and pulling on the top and bottom of the tire.
5
Use an OBD-II scanner to check for any related fault codes.

Solution

1. Preparation

Gather tools and parts needed for the replacement.
Tools Required:
- Socket set
- Torque wrench
- Hammer
- Slide hammer or wheel bearing puller
- Grease
- Jack and jack stands
Safety Warnings:
- Disconnect the battery before starting the work.
- Allow the vehicle to cool if it has been driven recently.

2. Remove Wheel and Brake Components

Loosen the lug nuts on the wheel while the vehicle is still on the ground.
Lift the vehicle and secure it with jack stands.
Remove the wheel completely.
Detach the brake caliper and support it without stressing the brake line.
Remove the brake rotor to access the wheel bearing.

3. Remove the Wheel Bearing

If applicable, remove the dust cap and cotter pin from the hub assembly.
Use a socket set to remove the axle nut (if present).
If necessary, use a slide hammer or bearing puller to extract the wheel bearing from the hub assembly.
Clean the hub area thoroughly where the new bearing will be installed.

4. Install New Wheel Bearing

Apply a thin layer of grease to the new wheel bearing.
Press the new bearing into the hub assembly using a bearing press or gently tapping it in with a hammer (make sure it's seated evenly).
Reinstall the axle nut and tighten it to the manufacturer's specified torque value (usually around 150-200 ft-lbs, check service manual).
Reinstall the dust cap and cotter pin if applicable.

5. Reassemble Components

Reattach the brake rotor and caliper to their original positions.
Reinstall the wheel and hand-tighten the lug nuts.
Lower the vehicle to the ground and torque the lug nuts to the manufacturer's specifications.