why does my GMC Sierra T1XX (2019-Present) shake when I brake?

GMC Sierra T1XX (2019-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

562 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix brake vibration issues in GMC Sierra T1XX (2019-Present). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool before working on brake systems to avoid burns.

Symptoms

•Shaking or vibration felt in the steering wheel or brake pedal when applying brakes
•Uneven wear on brake pads or rotors
•Grinding or squeaking noises during braking
•Vehicle pulls to one side while braking
•Increased stopping distance

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a runout gauge.
2
Check brake pads for wear and proper installation; measure thickness.
3
Examine suspension components (control arms, bushings) for wear or damage.
4
Verify tire balance and alignment by performing a visual inspection.
5
Scan for any error codes related to the brake system using an OBD-II scanner.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Dial gauge
•Torque wrench
•Bungee cord
•Brake grease
•Tire balancer

Parts Required

•Brake rotors
•Brake pads
•Suspension components (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a runout gauge.
2
Check brake pads for wear and proper installation; measure thickness.
3
Examine suspension components (control arms, bushings) for wear or damage.
4
Verify tire balance and alignment by performing a visual inspection.
5
Scan for any error codes related to the brake system using an OBD-II scanner.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Wear safety glasses and gloves.

2. Inspect and Replace Brake Rotors

Remove Wheel: Use a socket set to remove the lug nuts and take off the wheel.
Check Rotor Condition: Use a dial gauge to measure rotor runout; if greater than specifications (usually 0.002-0.005 inches), rotors may need to be replaced.
Remove Brake Caliper: Unbolt the caliper from the bracket and hang it using a bungee cord—do not let it dangle by the brake line.
Remove Rotor: Unscrew the retaining screws (if applicable) and slide the rotor off the hub.
Install New Rotor: Position the new rotor on the hub, secure with screws, and reattach the brake caliper.

3. Inspect and Replace Brake Pads

Check Pad Thickness: Measure the thickness of brake pads; replace if under 3mm.
Remove Brake Pads: Slide the old pads out of the caliper bracket.
Install New Brake Pads: Apply brake grease to the backing of the new pads and slide them into position.
Reassemble Caliper: Reattach the caliper over the new pads and torque bolts to manufacturer specifications (usually around 20-30 ft-lbs).

4. Suspension Inspection and Repair

Visual Inspection: Check control arms, bushings, and ball joints for cracks or excessive play.
Replace Worn Components: If any parts are worn or damaged, replace them as necessary.
Reassemble: Ensure all components are tight and securely fastened.

5. Wheel Alignment and Balancing

Balance Tires: Use a tire balancer to ensure all tires are evenly balanced.
Check Alignment: Measure and adjust the wheel alignment to manufacturer specifications.