how to fix GMC Sierra T1XX (2019-Present) when it won't start and just clicks

GMC Sierra T1XX (2019-Present)

Error Codes

1-3 hours

Time

medium

Difficulty

high

Severity

3 min read

495 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the no-start clicking issue in GMC Sierra T1XX (2019-Present). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working in the engine compartment.

Symptoms

•Clicking noise when turning the ignition key
•Dashboard lights dim or flicker
•No engine turnover or cranking
•Possible battery warning light illuminated
•Lights and accessories function intermittently

Diagnostic Steps

1
Check battery voltage using a multimeter; ensure it reads above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Attempt to jump-start the vehicle with jumper cables and a functioning vehicle.
4
Test the starter relay by swapping it with another identical relay in the fuse box.
5
Measure voltage at the starter solenoid with the key in the 'start' position to confirm power is reaching the starter.
6
Inspect the starter motor for physical damage or wear.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Socket set
•Wire brush
•Battery terminal cleaner
•Torque wrench
•Screwdriver set

Parts Required

•New battery (if necessary)
•New starter motor (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check battery voltage using a multimeter; ensure it reads above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Attempt to jump-start the vehicle with jumper cables and a functioning vehicle.
4
Test the starter relay by swapping it with another identical relay in the fuse box.
5
Measure voltage at the starter solenoid with the key in the 'start' position to confirm power is reaching the starter.
6
Inspect the starter motor for physical damage or wear.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the ignition is off.
Disconnect the negative battery terminal to prevent electrical shocks.

2. Battery Inspection and Replacement

Tools Required: Multimeter, socket set, wire brush, battery terminal cleaner.
Steps:
1. Clean battery terminals using a wire brush and battery terminal cleaner.
2. Reconnect the battery terminals securely.
3. If the battery is weak (below 12.4 volts), replace it with a new battery of the same specifications.

3. Starter Motor Inspection and Replacement

Tools Required: Socket set, torque wrench, screwdriver set.
Steps:
1. If the battery is good, locate the starter motor under the vehicle, usually near the transmission.
2. Disconnect the electrical connectors from the starter motor.
3. Remove the bolts securing the starter motor using a socket set.
4. Carefully take out the starter motor from its mount.
5. Install the new starter motor by reversing the removal steps, ensuring all connections are tight.
6. Torque the bolts to the manufacturer's specifications (refer to service manual for exact values).

4. Final Checks

Reconnect the negative battery terminal.
Ensure all tools and loose parts are removed from the engine bay.