why does my Genesis G70 shift hard between gears

Genesis G70 1st Gen (2018-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

499 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix hard shifting issues in Genesis G70. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool down before inspecting the transmission.

Symptoms

•Noticeable jerking or harshness during gear changes
•Delayed shifting or slipping between gears
•Unusual noises (clunking or grinding) during shifts
•Check engine light illuminated
•Increased RPMs without a corresponding increase in speed

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related codes.
2
Check the transmission fluid level and condition; look for discoloration or burnt smell.
3
Inspect the transmission fluid for leaks around seals and gaskets.
4
Test the battery and charging system, as low voltage can affect transmission performance.
5
Check the transmission mounts for wear or damage that could cause harsh shifting.
6
Inspect the throttle position sensor (TPS) for proper operation and calibration.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Fluid pump
•Jack and jack stands

Parts Required

•Transmission fluid (manufacturer-recommended type)
•Transmission filter (if applicable)
•Transmission mounts (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related codes.
2
Check the transmission fluid level and condition; look for discoloration or burnt smell.
3
Inspect the transmission fluid for leaks around seals and gaskets.
4
Test the battery and charging system, as low voltage can affect transmission performance.
5
Check the transmission mounts for wear or damage that could cause harsh shifting.
6
Inspect the throttle position sensor (TPS) for proper operation and calibration.

Solution

1. Preparation

Gather the necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety during electrical work.

2. Check Transmission Fluid

Remove the transmission dipstick and wipe it clean.
Insert the dipstick back into the tube and pull it out again to check the fluid level.
If low, add the manufacturer-recommended transmission fluid until the level is correct.
If fluid is burnt or contaminated, proceed to replace the fluid.

3. Replace Transmission Fluid

Drain the old transmission fluid using a fluid pump or drain plug.
Replace the transmission filter if applicable.
Refill with new, manufacturer-specified transmission fluid.
Replace the drain plug and torque it to the manufacturer’s specifications.

4. Inspect and Replace Transmission Mounts (if necessary)

Support the transmission with a jack and remove the bolts securing the transmission mounts.
Remove the old mounts and replace them with new ones.
Torque the new mounts to the manufacturer’s specifications.

5. Reconnect Battery and Clear Codes

Reconnect the battery terminals.
Use the OBD-II scanner to clear any stored error codes.
Test drive the vehicle to evaluate shifting performance.