how to fix my Ford Mustang S650 when the engine won't turn over

Ford Mustang S650 (2024-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

516 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the engine not turning over in Ford Mustang S650. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Electrical

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before working on components.

Symptoms

•Engine cranks but does not start
•No sound when the ignition key is turned
•Dashboard lights and electrical components are unresponsive
•Battery warning light illuminated
•Clicking sound from the starter when attempting to start

Diagnostic Steps

1
Inspect the battery voltage using a multimeter; ensure it's above 12.4 volts.
2
Check battery terminals for corrosion and tightness; clean and secure if necessary.
3
Test the starter motor by bypassing the ignition switch using a jumper wire.
4
Scan for error codes using an OBD-II scanner to identify any electrical issues.
5
Verify fuel pump activation by listening for the fuel pump sound when the ignition is turned on.
6
Inspect fuses related to the ignition and starting system for any blown fuses.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Jumper wire
•Socket set
•Wrench set

Parts Required

•Battery (if needed)
•Starter motor (if needed)
•Ignition switch (if needed)
•Fuel pump (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the battery voltage using a multimeter; ensure it's above 12.4 volts.
2
Check battery terminals for corrosion and tightness; clean and secure if necessary.
3
Test the starter motor by bypassing the ignition switch using a jumper wire.
4
Scan for error codes using an OBD-II scanner to identify any electrical issues.
5
Verify fuel pump activation by listening for the fuel pump sound when the ignition is turned on.
6
Inspect fuses related to the ignition and starting system for any blown fuses.

Solution

1. Preparation

Tools Required: OBD-II scanner, multimeter, jumper wire, socket set, wrench set.
Disconnect the negative battery terminal to prevent electrical shock during repairs.

2. Check and Replace Battery

Sub-steps:
1. Remove the battery terminals (negative first, then positive).
2. Test the battery with a multimeter; if the voltage is low, recharge or replace the battery.
3. If replacing, install the new battery and connect the positive terminal first, then the negative.

3. Inspect and Replace Starter Motor

Sub-steps:
1. Locate the starter motor under the vehicle.
2. Disconnect the wiring harness and battery cable from the starter.
3. Remove the starter motor mounting bolts using a socket set.
4. Replace with a new or reconditioned starter motor, ensuring proper alignment.
5. Reconnect the wiring harness and battery cable securely.

4. Inspect Ignition Switch

Sub-steps:
1. Remove the steering column cover to access the ignition switch.
2. Use a multimeter to test for continuity in the ignition switch when turned to the start position.
3. Replace the ignition switch if there is no continuity.

5. Verify Fuel System Operation

Sub-steps:
1. Check the fuel pump fuse and relay; replace if necessary.
2. If the fuel pump is not engaging, test the fuel pump directly by applying power to it.
3. If the pump fails to activate, replace it.