how to fix the AC blowing warm air in my Ford F-150 13th Generation (2015-2020)

Ford F-150 13th Generation (2015-2020)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

557 words

Problem Statement

Learn how to diagnose and fix the AC blowing warm air issue in your Ford F-150 (2015-2020). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Properly evacuate the AC system before disconnecting any refrigerant lines.

Symptoms

•AC compressor not engaging
•Warm air blowing from vents
•Unusual noises from the AC system
•Refrigerant leaks under the vehicle
•Poor airflow from the vents

Diagnostic Steps

1
Check the AC system settings to ensure it is set to the appropriate temperature and mode.
2
Inspect the AC compressor for any signs of damage or failure.
3
Use an OBD-II scanner to check for any error codes related to the AC system.
4
Verify the refrigerant level using a manifold gauge set.
5
Inspect the cabin air filter for clogs or obstructions.
6
Check for any blown fuses related to the AC system.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Manifold gauge set
•Vacuum pump

Parts Required

•AC compressor (if faulty)
•Cabin air filter (if clogged)
•Refrigerant

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the AC system settings to ensure it is set to the appropriate temperature and mode.
2
Inspect the AC compressor for any signs of damage or failure.
3
Use an OBD-II scanner to check for any error codes related to the AC system.
4
Verify the refrigerant level using a manifold gauge set.
5
Inspect the cabin air filter for clogs or obstructions.
6
Check for any blown fuses related to the AC system.

Solution

1. Preparation

Gather tools and parts required for the repair.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the negative battery terminal to prevent electrical shock.

2. Inspect and Repair the AC Compressor

Locate the AC compressor (usually near the front of the engine).
Check the electrical connector for damage and ensure it is securely attached.
If the compressor is faulty, remove the drive belt:
1. Loosen the tensioner pulley using a socket and ratchet.
2. Slide the belt off the compressor.
Remove the bolts securing the compressor to the engine using a socket set.
Disconnect the refrigerant lines (ensure the system is evacuated before this step).
Install the new compressor by reversing the removal steps and torque the bolts to the manufacturer’s specifications (usually around 20-25 ft-lbs).

3. Recharge the AC System

Connect the manifold gauge set to the low and high-pressure service ports.
Evacuate the system using a vacuum pump for at least 30 minutes to remove any moisture.
Recharge the system with the appropriate amount of refrigerant (typically R-134a), referencing the vehicle’s specifications (usually around 2-3 lbs).
Recheck the operation of the AC compressor and ensure it engages.

4. Inspect and Replace Cabin Air Filter (if necessary)

Locate the cabin air filter housing (usually behind the glove compartment).
Remove the glove compartment or access panel to reach the filter.
Remove the old filter and clean the housing.
Install the new filter in the correct orientation.