how to fix my Ford F-150 13th Generation (2015-2020) that stalls when accelerating

Ford F-150 13th Generation (2015-2020)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

563 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix engine stalling issues in Ford F-150 13th Generation (2015-2020). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before performing any work on the ignition or fuel system.

Symptoms

•Check engine light illuminated
•Engine stalling or cutting out during acceleration
•Rough idle when the vehicle is stationary
•Reduced power or sluggish response upon acceleration
•Increased fuel consumption
•Unusual engine noises (e.g., sputtering or backfiring)

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the fuel system for proper pressure; use a fuel pressure gauge to measure the fuel pressure against specifications.
3
Check the air intake system for any obstructions or leaks; inspect the air filter and intake ducts.
4
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for proper operation using a multimeter.
5
Examine the ignition system components, including spark plugs and ignition coils, for wear or damage.
6
Inspect the vacuum lines and intake manifold for leaks that could cause a lean condition.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fuel pressure gauge
•Multimeter
•Socket set
•Torque wrench
•MAF sensor cleaner

Parts Required

•Fuel pump (if needed)
•Air filter
•Spark plugs
•Ignition coils (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the fuel system for proper pressure; use a fuel pressure gauge to measure the fuel pressure against specifications.
3
Check the air intake system for any obstructions or leaks; inspect the air filter and intake ducts.
4
Test the throttle position sensor (TPS) and mass airflow sensor (MAF) for proper operation using a multimeter.
5
Examine the ignition system components, including spark plugs and ignition coils, for wear or damage.
6
Inspect the vacuum lines and intake manifold for leaks that could cause a lean condition.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the battery to prevent electrical shorts.
Ensure the vehicle is on a flat surface and secure with wheel chocks.

2. Fuel System Inspection and Repair

Sub-steps:
1. Remove the fuel pump relay from the fuse box.
2. Connect a fuel pressure gauge to the fuel rail.
3. Turn the ignition to the "On" position without starting the engine and check the gauge reading against manufacturer specifications (typically 30-45 psi).
4. If pressure is below specifications, check the fuel pump and replace if necessary.
5. Reinstall the fuel pump relay and reconnect the battery.

3. Air Intake and Sensor Cleaning

Sub-steps:
1. Remove the air filter and inspect for dirt or damage; replace if necessary.
2. Disconnect the MAF sensor and clean it with MAF sensor cleaner.
3. Inspect the intake ducts for any obstructions or cracks and replace as needed.
4. Reassemble the air intake system and reconnect the MAF sensor.

4. Ignition System Inspection

Sub-steps:
1. Remove the spark plugs and inspect for wear, carbon buildup, or damage; replace if necessary.
2. Test the ignition coils using a multimeter for proper resistance values according to specifications.
3. Replace any faulty ignition coils.
4. Reinstall spark plugs and ignition coils, ensuring proper torque settings.