why does my Ford Explorer Sixth Generation (2020-present) keep stalling

Ford Explorer Sixth Generation (2020-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

533 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix stalling issues in the 2020 Ford Explorer. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components.
•Allow the engine to cool before inspecting the intake system and fuel components.

Symptoms

•Check engine light illuminated
•Engine stalling during acceleration
•Rough idle when stationary
•Loss of power while driving
•Increased fuel consumption
•Erratic engine response

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics (OBD-II) system for error codes.
2
Inspect the fuel system for proper pressure and leaks using a fuel pressure gauge.
3
Check the air intake system for blockages or leaks.
4
Examine the spark plugs and ignition coils for wear or failure.
5
Test the throttle position sensor (TPS) for proper function with a multimeter.
6
Inspect the battery and alternator for proper voltage output.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Fuel pressure gauge
•Multimeter
•Socket set
•Torque wrench

Parts Required

•Fuel filter (if needed)
•Spark plugs (if worn)
•Ignition coils (if defective)
•Throttle position sensor (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's onboard diagnostics (OBD-II) system for error codes.
2
Inspect the fuel system for proper pressure and leaks using a fuel pressure gauge.
3
Check the air intake system for blockages or leaks.
4
Examine the spark plugs and ignition coils for wear or failure.
5
Test the throttle position sensor (TPS) for proper function with a multimeter.
6
Inspect the battery and alternator for proper voltage output.

Solution

1. Preparation

Tools Required: OBD-II scanner, fuel pressure gauge, multimeter, socket set, torque wrench.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the battery negative terminal to prevent electrical shorts.

2. Addressing Error Codes

Use the OBD-II scanner to retrieve any error codes.
Refer to a repair manual for your specific codes and follow troubleshooting steps for those codes.

3. Fuel System Inspection

Tools Required: Fuel pressure gauge.
Reconnect the battery.
Locate the fuel rail and connect the fuel pressure gauge.
Turn the ignition to the "ON" position (do not start) to check the fuel pressure.
If pressure is below specifications, inspect the fuel pump and filter for clogs or failures.

4. Air Intake System Check

Inspect the air filter and replace if dirty.
Check the intake manifold and hoses for leaks or blockages.
Clean the throttle body with an appropriate cleaner if carbon buildup is present.

5. Ignition System Inspection

Remove spark plugs and inspect for wear or fouling; replace if necessary.
Use a multimeter to test ignition coils for proper resistance; replace any faulty coils.

6. Throttle Position Sensor Testing

Disconnect the TPS connector and use a multimeter to measure resistance.
Check if the resistance changes smoothly as the throttle is opened and closed.
Replace the TPS if it shows irregular readings.