why does my Ford Explorer make a loud noise when accelerating

Ford Explorer Sixth Generation (2020-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

496 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix loud noise during acceleration in Ford Explorer. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Exhaust System

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Allow the engine to cool before inspecting or working on the exhaust system.

Symptoms

•Loud noise when accelerating
•Vibration felt through the steering wheel or floor
•Decreased acceleration or power loss
•Engine misfiring or rough running
•Check engine light illuminated

Diagnostic Steps

1
Inspect the exhaust system for leaks or damage.
2
Check the engine mounts for wear or deterioration.
3
Scan for error codes using an OBD-II scanner.
4
Inspect the intake system for loose or damaged components.
5
Test drive the vehicle to replicate the noise and note conditions.
6
Examine the transmission for any signs of slipping or unusual sounds.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Jack
•Jack stands
•Rubber mallet
•Socket set
•Pry bar
•Screwdriver set
•Flashlight
•Transmission fluid

Parts Required

•New engine or transmission mounts (if damaged)
•Exhaust components (if leaks or damage are found)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the exhaust system for leaks or damage.
2
Check the engine mounts for wear or deterioration.
3
Scan for error codes using an OBD-II scanner.
4
Inspect the intake system for loose or damaged components.
5
Test drive the vehicle to replicate the noise and note conditions.
6
Examine the transmission for any signs of slipping or unusual sounds.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is off.

2. Inspect Exhaust System

Sub-steps:
1. Raise the vehicle using a jack and secure it with jack stands.
2. Visually inspect the exhaust pipes, muffler, and catalytic converter for any signs of holes, rust, or loose connections.
3. Tap on the exhaust components with a rubber mallet to listen for hollow sounds indicating internal damage.
Tools Required: Jack, jack stands, rubber mallet.

3. Check Engine and Transmission Mounts

Sub-steps:
1. Locate the engine mounts and inspect them for cracks or separation.
2. Push down on the engine to see if it moves excessively.
3. For transmission mounts, check for similar signs of wear.
Tools Required: Socket set, pry bar.

4. Inspect Intake System

Sub-steps:
1. Open the hood and locate the air intake assembly.
2. Check all connections and clamps for tightness.
3. Look for cracks or leaks in the intake hoses.
Tools Required: Screwdriver set, flashlight.

5. Transmission Check

Sub-steps:
1. Check the transmission fluid level using the dipstick; add fluid if low.
2. Look for any signs of burnt fluid (dark color, burnt smell).
3. If necessary, consult a professional for transmission diagnostics.
Tools Required: Transmission fluid, dipstick.