how to fix Ford Explorer Sixth Generation (2020-present) traction control disabled error

Ford Explorer Sixth Generation (2020-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

605 words

Problem Statement

Learn how to diagnose and fix the Traction Control Disabled error in Ford Explorer (2020-present). Step-by-step guide with symptoms and solutions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent shocks or shorts.
•Allow the vehicle's components to cool before touching to avoid burns.

Symptoms

•Traction Control Disabled warning light illuminated on the dashboard
•Reduced traction in slippery conditions
•Activation of the anti-lock braking system (ABS) warning light
•Erratic or unresponsive throttle control
•Unusual noises from the wheels during acceleration

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific codes related to the traction control system.
2
Inspect the wheel speed sensors for dirt, damage, or disconnection.
3
Check the ABS module for any faults or communication errors.
4
Examine the traction control switch for proper operation.
5
Verify the condition of fuses related to the traction control system.
6
Inspect the vehicle’s battery and charging system to ensure proper voltage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Fuse puller or needle-nose pliers

Parts Required

•Wheel speed sensors (if faulty)
•ABS module (if necessary)
•Traction control switch (if faulty)
•Fuses (as needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify specific codes related to the traction control system.
2
Inspect the wheel speed sensors for dirt, damage, or disconnection.
3
Check the ABS module for any faults or communication errors.
4
Examine the traction control switch for proper operation.
5
Verify the condition of fuses related to the traction control system.
6
Inspect the vehicle’s battery and charging system to ensure proper voltage.

Solution

1. Preparation

Gather all necessary tools and parts.
Disconnect the negative battery terminal to ensure safety while working on electrical components.

2. Inspect and Replace Wheel Speed Sensors

Tools Required: Socket set, multimeter.
Sub-steps:
1. Locate the wheel speed sensors on each wheel assembly.
2. Disconnect the electrical connector from each sensor.
3. Use a multimeter to test the sensors' resistance; it should typically be between 1,000 to 2,000 ohms.
4. If any sensor is out of specification, replace it with a new one.
5. Reconnect the electrical connectors and ensure they are secure.

3. Check and Replace ABS Module (if necessary)

Tools Required: Socket set, OBD-II scanner.
Sub-steps:
1. Use the OBD-II scanner to check for any ABS module error codes.
2. If a fault code indicates a problem with the ABS module, proceed with replacement.
3. Remove the module by disconnecting the electrical connectors and unbolting it from its mount.
4. Install the new ABS module and reconnect all connectors.
5. Clear the error codes using the OBD-II scanner and verify functionality.

4. Test Traction Control Switch

Tools Required: Multimeter.
Sub-steps:
1. Locate the traction control switch on the dashboard.
2. Disconnect the switch from its connector.
3. Use a multimeter to test for continuity when the switch is activated.
4. If the switch fails the test, replace it with a new switch.

5. Check Fuses

Tools Required: Fuse puller or needle-nose pliers.
Sub-steps:
1. Locate the fuse box and identify fuses related to the traction control and ABS systems.
2. Inspect each fuse for continuity; replace any blown fuses with the same amperage rating.