how to change the oil on a Ford Explorer Fifth Generation (2011-2019)

Ford Explorer Fifth Generation (2011-2019)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

525 words

Problem Statement

Learn how to change the oil on a Ford Explorer Fifth Generation (2011-2019). Step-by-step guide with symptoms, diagnostic steps, and safety warnings.

Affected Component

Engine

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the engine is cool before starting the oil change.

Symptoms

•Engine oil light illuminated
•Engine noise due to low oil levels
•Sludge buildup in the oil
•Decreased fuel efficiency
•Engine overheating

Diagnostic Steps

1
Gather necessary tools and materials for the oil change.
2
Park the vehicle on a level surface and engage the parking brake.
3
Open the hood and remove the oil fill cap to allow for smooth drainage.
4
Lift the vehicle using a jack and secure it with jack stands.
5
Place an oil drain pan under the oil pan and remove the oil drain plug.
6
Allow the old oil to drain completely, then replace the drain plug and tighten securely.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Oil filter wrench
•Socket set
•Oil drain pan
•Funnel
•Torque wrench
•Rags

Parts Required

•Engine oil (5W-30 or 0W-20 depending on the engine)
•New oil filter (specify model)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Gather necessary tools and materials for the oil change.
2
Park the vehicle on a level surface and engage the parking brake.
3
Open the hood and remove the oil fill cap to allow for smooth drainage.
4
Lift the vehicle using a jack and secure it with jack stands.
5
Place an oil drain pan under the oil pan and remove the oil drain plug.
6
Allow the old oil to drain completely, then replace the drain plug and tighten securely.

Solution

1. Preparation

Tools Required:
- Oil filter wrench
- Socket set
- Oil drain pan
- Funnel
- Torque wrench
- Rags
Parts Required:
- Engine oil (5W-30 or 0W-20 depending on the engine)
- New oil filter (specify model)
Safety Warnings:
- Ensure the engine is cool before starting the oil change.

2. Remove Old Oil Filter

Using the oil filter wrench, carefully unscrew the old oil filter.
Allow any remaining oil in the filter to drain into the oil pan.
Apply a small amount of fresh oil to the rubber gasket of the new filter to ensure a good seal.
Install the new oil filter by hand, turning it clockwise until snug.

3. Add New Oil

Using a funnel, pour the recommended amount of new engine oil (usually around 6-7 quarts) into the oil fill neck.
Replace the oil fill cap once finished.

4. Check Oil Level

Start the engine and let it run for a few minutes, allowing the new oil to circulate.
Turn off the engine and wait a minute before checking the oil level using the dipstick.
Add more oil if necessary to reach the recommended level.

5. Clean Up and Dispose

Remove the oil drain pan and properly dispose of the old oil and filter at a recycling center.
Clean any spills with rags.