FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
my BMW 5 Series F10/F11 (2010-2017) stalls at traffic lights what could be wrong - BMW 5 Series
Home/Cars/BMW/5 Series/F10/F11 (2010-2017)/my BMW 5 Series F10/F11 (2010-2017) stalls at traffic lights what could be wrong

my BMW 5 Series F10/F11 (2010-2017) stalls at traffic lights what could be wrong

BMW 5 Series F10/F11 (2010-2017)

Error Codes
2-4 hours
Time
medium
Difficulty
medium
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
557 words

Problem Statement

The BMW 5 Series F10/F11 (2010-2017) is experiencing stalling issues when idling at traffic lights.

Estimated Time
2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect the battery before working on electrical systems.
  • •Allow the engine to cool before working on the intake or fuel systems.

Symptoms

  • •Engine stalling at idle
  • •Rough idle
  • •Check engine light illuminated
  • •Decreased fuel efficiency
  • •Increased emissions
  • •Difficulty restarting the engine after stalling

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •Check the fuel pressure:
  • •Locate the fuel rail service port and connect the fuel pressure gauge.
  • •If pressure is low, check the fuel pump and filter for issues.

Parts Required

  • •Idle air control valve (if replacement is necessary)
  • •Throttle position sensor (if replacement is needed)
  • •Fuel filter (if low fuel pressure is indicated)

Additional Information

Estimated Time
2-4 hours
Difficulty
medium
Severity
medium
Tools Required
3 items
Parts Required
3 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Gather all necessary tools and parts.
  • Disconnect the battery to ensure safety while working on electrical components.
2. Fuel System Inspection
  • Tools Required: Fuel pressure gauge, wrench set
  • Check the fuel pressure:
    • Locate the fuel rail service port and connect the fuel pressure gauge.
    • Start the engine and observe the pressure reading; it should match the manufacturer's specifications (typically around 50-60 psi).
    • If pressure is low, check the fuel pump and filter for issues.
3. Throttle Position Sensor Testing
  • Tools Required: Multimeter
  • Test the TPS:
    • Locate the TPS on the throttle body.
    • Disconnect the TPS connector.
    • Set the multimeter to measure resistance and connect the probes to the TPS terminals.
    • Move the throttle plate and monitor the resistance change; it should vary smoothly without dropouts.
4. Idle Air Control Valve Cleaning/Replacement
  • Tools Required: Socket set, cleaning solvent
  • Clean or replace the IAC valve:
    • Remove the IAC valve from the throttle body.
    • Clean the IAC valve with appropriate solvent to remove carbon deposits.
    • If cleaning does not resolve the issue, replace the IAC valve with a new one.
5. Vacuum Leak Inspection
  • Tools Required: Smoke machine or soapy water solution
  • Check for vacuum leaks:
    • Use a smoke machine to introduce smoke into the intake system and observe for leaks.
    • Alternatively, spray soapy water on vacuum hoses and connections; bubbles will indicate a leak.
    • Replace any damaged vacuum hoses found during inspection.