ABS light on A6 C7

Audi A6 C7 (2011-2018)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

Error Code: C0035-C0051, C0110, C1234-C1237

4 min read

628 words

Problem Statement

Learn how to diagnose and fix the ABS light issue on your Audi A6 C7 with this detailed guide. Follow step-by-step instructions to ensure your ABS system functions correctly.

Error Code

C0035-C0051, C0110, C1234-C1237

Affected Component

Anti-lock Braking System (ABS)

Estimated Time

2-4 hours

Symptoms

•ABS warning light illuminated on the dashboard
•Possible traction control light also illuminated
•Brakes may feel firm or unresponsive during hard braking
•ABS may not activate during an emergency stop

Diagnostic Steps

1
Check the ABS fuse
2
Inspect the wheel speed sensors and wiring for visible damage
3
Check brake fluid level and condition
4
Connect an OBD-II scanner capable of reading ABS codes
5
Read and record any ABS-related trouble codes
6
Identify the affected wheel speed sensor if indicated by fault codes
7
Inspect ABS module and pump if indicated by fault codes

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner with ABS capability
•Multimeter
•Basic hand tools (screwdrivers, socket set, etc.)
•Jack and jack stands

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the ABS fuse
2
Inspect the wheel speed sensors and wiring for visible damage
3
Check brake fluid level and condition
4
Connect an OBD-II scanner capable of reading ABS codes
5
Read and record any ABS-related trouble codes
6
Identify the affected wheel speed sensor if indicated by fault codes
7
Inspect ABS module and pump if indicated by fault codes

Solution

When the ABS light is illuminated on your Audi A6 C7 (2011-2018), it indicates a potential issue with the Anti-lock Braking System. ABS is crucial for maintaining steering control during hard braking and preventing wheel lockup. Here's a detailed guide to diagnose and resolve the issue:

Tools Required:

OBD-II scanner with ABS capability.
Multimeter.
Basic hand tools (screwdrivers, socket set, etc.).
Jack and jack stands.

Step 1: Initial Inspection

Visual Inspection:
- Check the ABS fuse. Refer to the vehicle's manual for the exact location.
- Inspect the wheel speed sensors and wiring for visible damage.
- Check brake fluid level and condition.
OBD-II Scan:
- Connect an OBD-II scanner capable of reading ABS codes to the vehicle's port located under the dashboard.
- Turn the ignition to the 'ON' position without starting the engine.
- Read and record any ABS-related trouble codes.

Step 2: Code Analysis and Troubleshooting

Common Error Codes:
- C0035-C0051: Wheel speed sensor issues.
- C0110: ABS pump motor circuit failure.
- C1234-C1237: ABS hydraulic unit issues.
Wheel Speed Sensor Testing:
- If fault codes indicate a wheel speed sensor issue:
  - Identify the affected sensor.
  - Jack up the vehicle and secure it on jack stands.
  - Remove the wheel to access the sensor.
  - Disconnect the sensor's electrical connector and inspect for corrosion or damage.
  - Use a multimeter to check sensor resistance. Refer to the vehicle’s service manual for specific resistance values.
  - Replace the sensor if it shows open circuit or short circuit.

Step 3: ABS Module and Pump Testing

If the fault codes point towards the ABS module or pump, further testing is required:
1. ABS Module:
  - Inspect electrical connectors for corrosion or damage.
  - Check the power and ground connections using a multimeter.
2. ABS Pump:
  - Listen for pump activation noise when the ignition is turned on.
  - If the pump does not activate, check the relay and fuses associated with the ABS pump.
  - If the pump relay and fuses are good, the pump motor may need replacement.

Repair Instructions:

Replacing a Wheel Speed Sensor:

Remove the Sensor:
- Disconnect the sensor’s electrical connector.
- Remove the mounting bolt using the appropriate socket and carefully extract the sensor.
Install the New Sensor:
- Clean the mounting area.
- Install the new sensor and secure it with the mounting bolt.
- Reconnect the electrical connector.
Reassemble and Test:
- Reinstall the wheel and lower the vehicle.
- Clear the ABS fault codes using the OBD-II scanner.
- Test drive the vehicle to ensure the ABS light remains off.

Replacing the ABS Module or Pump:

Module Replacement:
- Disconnect the battery.
- Remove the electrical connectors and mounting bolts from the ABS module.
- Install the new module and reconnect everything.
Pump Replacement:
- Ensure the brake system is depressurized.
- Disconnect the brake lines and electrical connectors from the ABS pump.
- Install the new pump and reconnect all lines and connectors.
- Bleed the brake system to remove air.

Final Steps:

After repairs, always clear the fault codes using the OBD-II scanner.
Perform a road test to ensure the ABS system functions correctly and the warning light stays off.

By following these detailed steps, you should be able to diagnose and resolve the ABS light issue on your Audi A6 C7. If problems persist, consider consulting a professional mechanic for further diagnosis.